We rebuild Autoprop H5 and H6 propellers in our Virginia workshop. Send us your serial number and you’ll get a full price straight back. You don’t need to book anything or take a photo to get a quote.

Autoprop H5 and H6 rebuilds

We strip the hub, clean and inspect the hub and blades, fit a new bearing kit, then reassemble, torque and grease it. Once the propeller arrives, it is usually back in the box within 2 to 3 days, with a 3-month warranty on the workmanship.

Model Bearing type Kit Labor (guide)
H5 Roller bearing, tab screw APP-H5-BK-TS $295
H5 Roller bearing, tab washer APP-H5-BK-TW $295
H5 Ball bearing APP-H5-BK-BB $295
H6 Roller bearing, tab screw APP-H6-BK-TS $395
H6 Roller bearing, tab washer APP-H6-BK-TW $395
H6 Ball bearing APP-H6-BK-BB $395

The bearing kit is charged at its current store price, on its own line, so you can check it against the store and see there is no mark-up. Return shipping is at cost. Shaft-drive and saildrive Autoprops are serviced the same way.

Larger Autoprops, such as the H9, are price on request, because the parts are ordered in for each job.

Get a quote

Fill in the form below and the full price lands in your inbox within a minute: labor, kit, deposit and turnaround. Not sure which propeller you have? Pick “Not sure”, reply with the serial number stamped on the hub, and you’ll have a price the same day.

To go ahead

  1. Pay the $150 booking deposit. It is credited in full to your final invoice.
  2. Send a few photos of the hub and blades if you can. If the propeller is still on the boat, that’s fine: send it in when it comes off and we’ll inspect it on arrival.
  3. We send you the shipping address and packing notes.
  4. We inspect it, rebuild it and ship it back with tracking, with the final invoice less your deposit.

What the inspection can find

  • Good condition, or surface rust: we rebuild it in the workshop at the price quoted.
  • Worn bearing tracks: a new kit won’t cure it, and the hub needs machining at the factory. We quote that before any work starts and handle the shipping and paperwork.
  • Bronze that has deteriorated: bronze that hasn’t been looked after can turn brittle, and it cracks rather than machines. We can’t rebuild it safely, so we stop there and send you the inspection report. Your $150 deposit is then credited against a new propeller.

Loose blades: free re-torque

A loose blade is a lost blade that hasn’t happened yet, so we don’t want anything to put you off sending it in. It’s a mini rebuild, free of charge. We take the blades off, clean the threads and inspect everything, then refit and torque each blade and grease the hub so the bearings are right. You pay the carriage only.

If the inspection finds anything else, you get a short report and a quote. There’s no obligation: the re-torque goes ahead either way.

Lost blade: top priority

If you have lost a blade, it goes to the front of the queue. Email us the serial number and photos, and you will have a price the same day.

Every Autoprop blade set is dynamically balanced at the Bruntons factory, so the propeller has to make the trip. We arrange the collection, packing instructions and customs paperwork. Bruntons fit and balance the new blade as a priority job and ship it straight back, and we keep you updated with tracking the whole way. Afterwards we inspect the rest of the propeller and the bearings, so it doesn’t happen twice.

Re-pitching

Re-pitching is the cure when the engine can’t reach its rated rpm, or races past it. Getting it right takes more than a guess, so we work it out with you first, free of charge:

  1. You run a simple sea trial and fill in our sea trial sheet: boat speed at set rpm steps up to full throttle, two runs in opposite directions, plus the wind, sea, engine and gearbox details.
  2. We plot your results against the engine’s demand curve.
  3. We run the numbers through Bruntons’ propeller software.
  4. We settle how much pitch to add or take off to bring the rpm where it should be.

Once the change is agreed, the propeller goes to the Bruntons factory to be re-pitched and balanced on their specialist machine. We quote it at that point and handle the shipping and customs paperwork.

Varifold and SigmaDrive

Varifolds are built like tanks and simple enough to look after yourself. We supply the parts (anodes, buffer pads, pivot pins and fasteners) and can point you to the how-to videos.

Smaller SigmaDrive units are replaced when they wear rather than serviced. We supply replacement units, parts and fitting advice for the whole range.

Everything can be done by email. Send us your serial number and we’ll take it from there.